How to Repair Vacuum Cleaner – Step by Step GuidePosted on July 9th, 2011 No comments
Vacuum cleaners typically last 8 to 12 years depending on its quality, frequency of use and general maintenance. Through maintenance and repair of your vacuum cleaner as needed, you can increase longevity and reduce the actual cost.
There are two common types of vacuum cleaners: upright and canister. The upright vacuum cleaner has the motor and beater bar in the same unit. A vacuum cleaner has the motor and storage bag into the container and beater bar connected to a separate power head, with the two devices via a hose.
How vacuum cleaners work hand
An upright vacuum cleaner uses a motor and fan to pull dirt from the surface and deposit in your pocket. Dirt is loosened and swept called into the vacuum with a rotating brush bar bat. The handheld vacuum cleaner is the operator using the handle on the bag and controls are mounted out. The operation is simple. Maintenance and repairs are easy to perform.
Vacuum cleaners work as
A vacuum cleaner puts most of its weight (suction motor, filter, and cord storage bag) in a separate unit to power the light head.
With a long hose, the ship in the middle of the room and placed power in the head moved more easily. This design makes it possible to use larger and more powerful engines.
As with an upright vacuum cleaner that loosens dirt with the club’s bar, located in the power head and is driven by a smaller motor. Dirt is pulled through the tubing of the main motor in the container. Wheels on the container makes it easy to transport.When the fan is in a can vacuum more isolated than the fan in an upright vacuum, it is usually less prone to injury.
How you can repair an upright vacuum cleaner
The following tips provide a simple guide to the maintenance of an upright vacuum cleaner on / off, beater bars, belts, debris fan and motor. You will also learn to repair an on / off switch, a power-head-wire connection, a striker bar, a motor and a cable drum of a vacuum cleaner.
Maintenance of an on / off switch: Due to repeated use, is a vacuum cleaner on / off switch may malfunction. Fortunately, for most models, the switch easy to reach and test. Some are fixed in place with rivets, but spends most of the screws. To test and replace the switch:
Step 1: Make sure the vacuum is pulled, expose, remove the cover plate on the back of the switch. The switch can be on the handle or case.
Step 2: Check the wires to ensure they are fully connected to the switch.
Step 3: Use a continuity tester or multi-tester to ensure that there is an open circuit when the switch is off, and a closed circuit when it is running.
Step 4: If there are problems with the circuit, or if the switch does not test properly, remove and replace the switch with a developed, representing a replacement.
Maintaining a beater bar: The bar bat upright vacuum cleaner is one of the first contacts in your upright vacuum cleaner with dirt. It is also one of the first components to be serviced.
The club bar is a circular cylinder with an offset number of brush fibers. The brushes can wear to the roller may be damaged, can solve the CAP will be lost, or can solve the drive belt. To remove and replace the Club Bar:
Step 1: To investigate the club’s bar, turn on the vacuum head. The club bar will be at the forefront of the house.
Step 2: Remove the clips are removed at each end, drive belt, and lift the beater bar from the case.
Step 3: To dismantle the Club Bar, remove the end cap and flange, pull the brush out of the case.
Step 4: If worn, replace the brush. If broken, cap, flange, or event. If necessary, replace the entire club bar.
Maintaining a belt: The tape is in an upright vacuum cleaner power from the motor to the beater bar. The drive belts should be checked once a month to ensure it is in good condition. Some hammers have an adjustment that the belt can be tightened or loosened. To replace the drive belt:
Step 1: Remove one end of the striker bar (see “Maintaining a beater bar”) from the vacuum enclosure.
Step 2: Loosen the drive belt from engine pulley and remove the cash from all the racket.
Step 3: Slide the new drive belt for the beater bar and around the pulley.
Step 4: Install the bat and then adjust the drive belt as needed.
Maintaining a fan Dirt: The dirt-fan in an upright vacuum cleaner is located under the engine. He retires dirt swept through the club bar in the bag. In most cases, remains the fan not to replace, just regular maintenance. Here is what you need:
Step 1: Remove the bonnet and remove the engine from the vacuum frame. The fan will be at the bottom of the engine.
Step 2: Clean the fan blades and base with a damp cloth. Check the blade for damage caused by vacuuming solid objects.
Step 3: Remove or release the dirt from the fan motor shaft to inspect and clean the back.
Step 4: Check whether the motor shaft needs lubrication.
Step 5: If dirt needs to be replaced fan, make sure the new part is a genuine spare parts. Remove the old unit to control an appliance parts store for replacement.
Maintenance of an engine: the most upright vacuums are designed for reasonably long lifetime. But some will take longer than others. Much depends on the quality of the engine. When a vacuum motor is not unexpected work, check the power cable, fan (for jam), and on / off button. It is also possible that you have a faulty engine. Here is how to find out:
Step 1: If you suspect that the engine is defective, the first test of the motor brushes with a continuity tester or multi-tester.
Step 2: Rotate the motor shaft by hand or beater bar. The engine must be continuity.
Step 3: If not, replace the brush or a vacuum cleaner to a machine shop did it. If you want the engine beyond repair, you should vacuum the entire state, as the price of a new engine is a great investment.
How to repair a vacuum cleaner
A vacuum cleaner has its own set of repair procedures. Here they are:
Maintenance of an On / Off Switch: How to switch on most small devices, on / off switch on a vacuum cleaner gets plenty of use. Given the ease of repair and replacement costs down, this contact one of the first component is to verify whether a vacuum is not turned on or off properly. To test and replace the switch:
Step 1: Free access or remove the container housing on the back of the switch.
Step 2: Use a continuity tester or multi-tester to ensure that there is an open circuit when the switch is in OFF position and a closed circuit when the switch is in the ON position.
Step 3: Check the cabling and connectors to ensure they are properly connected.
Step 4: Remove, if not properly test the switch, this and replace it. Some of the contacts on the housing are fastened with screws, clips or friction with other snaps. A few are riveted there.
The maintenance of a power-director-wire connection: An advantage of vacuum cleaner is that the part that is easily pushed or pulled across the floor as a single unit upright vacuum. One drawback is that power will only be delivered to the tank, and then separate the power head.
The wire connection between the two devices is often a source of problems in better quality vacuum cleaner. The reason is that there are four sections to make the lead: from the tank to the hose from one end of the hose to another, from one end of the steering tube to the other, and because the head itself. At the end of each chapter has a wire connection. If the connection is not established enough, has the power to head is not in operation or intermittent.
In most cases, maintenance of motor-head-wire connection only that each port will be checked and tightened if necessary. If a particular context, often has a bad connection, you can clean the male and female relationships with a small piece of sandpaper and a can of compressed air.
Broken wires or worn insulators can sometimes go back and wrapped with electrical tape. But the wire inside the tube, requires that the tube be replaced as well.
Maintaining a beater bar: The bar bat waiting for a can of vacuum in much the same way as you upright on a device. Here’s how:
Step 1: Remove the clips at each end of the striker bar and pull it and belt from the power-key affair. In many cases, all you have to do to clean the brush and the two ends. Remove excess reach pet hair and carpet fibers that wounds in them.
Step 2: If necessary, remove the beater bar end cap and flange to remove the brush from the bay and clean or replace.
Step 3: Check the drive belt and replace if worn or damaged.
Step 4: After the reinstallation of the club’s bar, make sure there is enough tension on the tape by pulling the bar to rotate the belt. If the tape is loose, adjust it according to instructions in the manual.
The maintenance of a motor: The motor of a vacuum cleaner is easy access to most models. To test and replace the motor brushes:
Step 1: Open the top cover on the container and remove the hood to reveal the engine itself.
Step 2: Insert the probes of a continuity tester or multi-tester to the two wires leading from the motor on / off switch.
Step 3: Rotate the motor shaft a few revolutions by hand. The engine must be tested as a closed circuit with some resistance. If an ohmmeter shows infinite resistance or no resistance, the motor is probably damaged.
Step 4: Check the motor, the brushes in the same way if they are available. Replace brush if necessary.
For other engine repairs, take the equipment into an appliance repair or engine repair shop. If the engine needs replacing, should assess the overall condition of the vacuum and replacing the entire unit.
Maintaining a Cord Reel: The wheel is mounted on a vacuum cleaner a gadget that makes it easy to facilitate storage of the cable. It is not clean everything. The cable drum unit is usually located on the back of the container.
An inside source has enough tension to pull the cable on a roll. The cable drum playing, rope in a circle, the internal end of the cable must also move in a circle. At the same time it must be electrically connected to the motor.
For this to work, the power cable to a rotating switch called commutator block attached. It is a round conductor of electricity, electricity from the inner end of the cable to a stationary block yesterday. If the blocks are dirty or corroded, they will not pass power to the motor. To clean and remove or replace the cable drum:
Step 1: Open the top cover of the container. And probably the engine and – - of the vacuum chamber further closing the lid will protect the cable drum.
Step 2: Depending on whether you are cleaning or replacement of the cable drum, it may be necessary to remove from the case. You can find clips or screws holding it in place and do regret. If necessary, cut the two wires of the cable drum motor. In some cases you may be able to repairs and adaptations without affecting the motor cables to do.
Step 3: Clean the power cord from dirt, then clean the collector and stationary block with isopropyl alcohol on a soft cloth. If pitted, the blocks are easily sanded and wiped clean.
Step 4: Adjust the spring, as necessary, and install the unit in reverse order, replacing each cut wires.General Information canister vacuum cleaner repair, how to, how to repair vacuum cleaner, maintain vacuum cleaner, repair, repair upright vacuum cleaner, repair vacuum cleaner motor, vacuum cleaner maintenance, vacuum cleaner repair
Leave a reply